Massoth Navigator issues

LGB-Sid

LGB-Sid

Registered
Country flag
I am using a Nav with a LGB 55006p, I recently decided it would be good to go wireless, so I bought the Massoth PC module to update the Nav so it can be converted to wireless, that failed I have tried three PCs on two diffrent operating systems and non can update the Nav firmware, all end with the read no data 117 error, but I can update the PC module firmware, so it is working, I can all so read and write CV's on the programming track OK.

I also bought the Switch Decoder 4K, if I connect it up to the programming track I can read the CV's OK via the PC module and the Point motor switches when it reads so that is working OK

If I use the Nav second function and tell it to switch the point motor nothing moves , it should and is on address 1 as its still set to factory defaults.

Beginging to think I have a naff nav or I am missing something basic here ? as apart from select an engine and operate it with the nav, it won't control a Switch decoder or up-date when teathered to the PC module.
 
Two things you could try..

1. Can you load the version of software the Nav. is already running?

2. Are you trying to 'jump' any intermediate versions of software. - This used to be a no-no with decoders, not sure if it will have changed by now?
 
The Nav is on 2.00d, I don't think there is one in between that and 2.1 ?, I know the 2.1 says it is a big update, I don't have access to any other firmware for it the only one listed to upload is the 2.1 so can't try the 2.00. Its odd I can not control a switch decoder with it through the LGB central station, which I assume I should be able too ?.

I have been searching the net to see if you can connect the LGB central station to the PC module via the Dimax bus, reason was it is the only other thing I have that I could talk to through that connector to rule out a problem with PC module.
 
You can update from 2.00d directly to 2.1. 2.1 contains the firmware changes for the 2.4GHz wireless protocols and selection. There was a 2.01 which introduced support for a new display but you should not need to use this.

Have you tried forcing the Navigator into update mode before you try the update? If I recall, you need to hold the right arrow button down when you plug it into the PC module.
Also, I find it best to recycle the power to the PC module just before you do any firmware upload especially if you have been messing with CVs.
 
muns said:
You can update from 2.00d directly to 2.1. 2.1 contains the firmware changes for the 2.4GHz wireless protocols and selection. There was a 2.01 which introduced support for a new display but you should not need to use this.

Have you tried forcing the Navigator into update mode before you try the update? If I recall, you need to hold the right arrow button down when you plug it into the PC module.
Also, I find it best to recycle the power to the PC module just before you do any firmware upload especially if you have been messing with CVs.
Click to expand...

Hi , I have tried the recycle power to the PC module and yep you hold the Right button down when you plug it in and the screen then shows Software-Update so I assume that's in update mode.

I have a shorter lead to tether with so I tried that but no difference, still the same error. but it was worth a go, as running out of chickens to sacrifice :) unless frozen ones count..

I also tried a factory reset on the Nav so it's back to a standard setup in case but that didn't help just lost all my Locos that were set up in it :)
 
Still no joy with this Nav so I have emailed Massoth to see if they have any ideas on the Read No Date 117 error.
 
Have you read through this thread?

www.gscalecentral.net

Massoth Decoder Firmware Update Issues (again!)

Apologies for yet another thread on this but I'm struggling to put a new firmware file onto a decoder and can't for the life of me see what I'm doing wrong. I'm using the Massoth PC Module (USB version - 8175201) and the latest Massoth Service Tool program which works fine for...
www.gscalecentral.net www.gscalecentral.net

Talking decoders here, but the same rules apply.. Must have a certain level of software to jump to a higher level, etc.

PhilP.
 
PhilP said:
Have you read through this thread?

www.gscalecentral.net

Massoth Decoder Firmware Update Issues (again!)

Apologies for yet another thread on this but I'm struggling to put a new firmware file onto a decoder and can't for the life of me see what I'm doing wrong. I'm using the Massoth PC Module (USB version - 8175201) and the latest Massoth Service Tool program which works fine for...
www.gscalecentral.net www.gscalecentral.net

Talking decoders here, but the same rules apply.. Must have a certain level of software to jump to a higher level, etc.

PhilP.
Click to expand...

Hi I have read throught it,but didnt come to any conclusions to sort out why I am stuck, as Muns says I should be able to go from 2.00d to 2.1 as the only version inbetween was a 2.01 that allows use of a new display ? but 2.01 is not an option in the Massoth software to update too, just the 2.1 is listed.
 
I Got a quick response from Massoth, They said remove any battires if you have put them in and use the Piko version to upgrade the Nav, and guess what it upgraded it , I had already renoved the batteries on previous attempts :) I asked if I then need to do it again with the Massoth version and the answer was no, as its the same software just a diffrent loading screen, mine now says its a Piko Navigator :D
 
Oh dear what a mess, I am staying with whatever I was last upgraded to 3 years ago, same as I have never gone beyond windows 98 on my aged PC. Why break it it if it ain’t broke?
 
Greg Elmassian said:
Massoth said to update with a Piko version? very strange.
Click to expand...

Yep that was the reply from them, they said if it won't update with the Massoth version try the Piko one, its the same Firmware just a different front end :)
 
Last edited:
I wondered that, so I asked if I needed to do that , which is when they said the only difference between the two was the loading screen saying Massoth or Piko, so I don't need too. I must admit I was tempted but after the hassle of getting it to work I decided I can live with it saying Piko on boot up :)
 
You must log in or register to reply here.
Back
Top Bottom