Converting modern LGB Stainz starter set loco to digital operation

norwegian

Registered
Hey all. Beginner G scale modeller here. I got the classic LGB starter set a few weeks ago (see photo). Now I bought another digital locos and wagons, and I want to convert the analog Stainz to digital as well. I bought the LGB digital conversion kit, as well as the Marklin decoder programmer so that I could load in a Stainz-like sound program for it. Problem seems to be that there are very few and sometimes confusing guides on how to convert this classic loco to digital, and most of them seems to focused on older versions. I got mine this year, and the production number indicates that it was produced this year (2026). Still very confused about if this loco even has some kind of decoder plug at all, and I am struggling with some of the steps of the dissasembly. Right now I am not able to reach the circuit board inside the boiler to get it examined properly. There is some mention of some plastic clips that needs to be pressed in in order to open up the bottom half of the boiler, but it seems to be inaccessible. Would love some tips here.

Also, do you think that the LGB conversion kit will work at all? It does come with another adapter that allows for soldering if there is no 28 or 10 plug on the locos board.

I will be using it together with my Marklin CS3 controller (which I already use for my extensive H0 collection). Would love some tips :)

IMG_5733.jpegIMG_7621.jpegIMG_7619.jpeg
 
Hi Norwegen,

I have some experience of fitting a DCC decoder into various Stainz models. The Stainz that you have can be fitted with a Massoth L (No Sound), LS (Sound) or Mxion equivalent. The Massoth L decoder fits directly onto the main circuit board which is located in the boiler. The Massoth LS does not use the main circuit board but fits inside the boiler. This is not the case for the decoder that you have bought as it is too big to fit into the boiler.

Here is a link, that I hope will help you fitting a Massoth LS : https://www.massoth.de/wp-content/uploads/2020/04/LGB-2x212-Stainz_EN_massoth_umbaubericht.pdf

I hope that you find this useful. Do let me know if you want further information

Regards

Martin
 
Welcome to the Forum!

As you have discovered, the Stainz may be a Starter Set loco,but is not one I would recommend as a 'starter' to fit a decoder. - Especially sound..

They are a bit of a 'Chinese puzzle' to take apart.

PhilP.
 
It won't work in the sense that it simply won't physically fit in a Stainz. It is designed for locos with much more interior space.

As noted above, one of the small Massoth decoders would be the best way to go.

It could probably still be used, but only if you put it in the cab, where it would be very visible.... if you didn't mind that, then it could be done. Otherwise, if you are able to return that package for a refund then I would do that, and go one of the routes that has already been suggested...

Jon.
 
I've recently fitted mine with a mXion L decoder. Reasonably straightforward if a bit involved to get it apart. The decoder just plugs straight onto the motherboard inside the boiler shell.

Im planning to convert the sound on mine in the future and from what I can see, it is possible to feed a SUSI cable through the existing wiring channels into the roof space where the stains sound module and speaker are located. The SX6 from mXion can then replace the default sound generator and it looks like it would fit into that space.
 
I've recently fitted mine with a mXion L decoder. Reasonably straightforward if a bit involved to get it apart. The decoder just plugs straight onto the motherboard inside the boiler shell.

Im planning to convert the sound on mine in the future and from what I can see, it is possible to feed a SUSI cable through the existing wiring channels into the roof space where the stains sound module and speaker are located. The SX6 from mXion can then replace the default sound generator and it looks like it would fit into that space.
That sounds like a solution..
Though:
Does the mxion L have a SUSI connector? - I am not familiar with the mXion range.

PhilP.
 
That sounds like a solution..
Though:
Does the mxion L have a SUSI connector? - I am not familiar with the mXion range.

PhilP.
The Mxion has a SUSI connector:

"The mXion DRIVE-L is a powerful 3.5A (4A peak) locomotive decoder with sensitive control. The DRIVE-L features 6 function outputs and 2 contact inputs. On all function outputs, the DRIVE-L can perform a wide range of special and imitation simulations (e.g., TV, delayed on/off, neon, gas lamps, fire, dimming, etc.). Servo functionality is also included. A 'Swiss mapping' is available as well. In addition to the 'Swiss mapping' and American special functions, the DRIVE-L has a total of over 19 special functions and special lighting functions. Digital and analog load regulation is also implemented. The extensive mapping up to F28 allows for many functions. With the innovative random generator, various simulations (e.g., boiler fire) can be triggered randomly. Moreover, no additional boiler fire module is needed. Of course, the DRIVE-L has a SUSI interface and labeled terminals, making it easy"

Martin
 
Stainzes of any age are b*ggers to get apart! However once you've done it, and figured out all the little tricks, it's relatively straightforward to do it again... :D

Jon.
 
Hey all! First, thanks for welcoming me to the forum!

So I managed to get the boiler out and separated. And as I feared, there is no digital plug for DCC, and the circuit board is way narrower than the retrofit decoder. Guess I am so used to this being common in the HO world that I took DCC readiness it for granted. But thats ok :). I will see what my options are for returning / reselling the decoder I bought.

Once I got the hang of it, disassembling and reassembling this modern Stainz were easier than I thought.There are plugs for every wire, and not as many screws as in the older versions. I managed to get it back in one piece now in under an hour and its back on the analogue loop around the xmas tree!

For digital, I really want sound and lots of functions, and the Mxion mentioned by @MTheStrong set looks like a good option! (unless it only plays xmas songs :D). Will check it out!

Thanks for the help so far!

IMG_7652.jpeg

IMG_7653.jpeg
 
That IS a digital-ready board in your Stainz, but it's for a direct plug-in decoder like the old LGB 55021, or more modern equivalents like the Massoth L or the mXion L.

In your top photo, there are eight plug-in sockets for the pins on the decoder - two are directly underneath the block of red DIP switches, then four more in the middle, and two more at the bottom. You simply cut the wiring loom off the decoder board, then just push the pins into those sockets.

Jon.
 
The simplest option (in terms of easiest to fit) will be the mXion decoder, plugged directly onto the loco board, then their SX6 sound module plugged into the SUSI socket on the decoder and tucked away somewhere in the cab. For the speaker, you could either use the mXion one that comes in the little plastic cube housing, or you could actually re-use the speaker from the Stainz's own basic chuff system, which is inside the cab roof - just cut any connections between the speaker terminals and it's own simple sound board, and solder the wires from the SX6 speaker plug onto the terminals of the speaker...

Jon.

Edit: my main reason for suggesting the re-use of the factory fit speaker is to simplify the speaker installation - why not use what is already there, then you don't have to figure out somewhere to mount a new speaker? Having said that, the mXion speaker box would probably fit in the roof compartment of the Stainz after taking the old "sound" unit out... so it's a matter of choice really! I would probably put the SX6 module on the cab floor, wrapped in some black tape to disguise it - at normal viewing angles it will hardly be visible.
 
Last edited:
That IS a digital-ready board in your Stainz, but it's for a direct plug-in decoder like the old LGB 55021, or more modern equivalents like the Massoth L or the mXion L.

In your top photo, there are eight plug-in sockets for the pins on the decoder - two are directly underneath the block of red DIP switches, then four more in the middle, and two more at the bottom. You simply cut the wiring loom off the decoder board, then just push the pins into those sockets.

Jon.
Oh, you are right. But that decoder seems to be an older type as you say. So might lean towards the mXion. Found the non-xmas version: Digitalisierungsset für LGB Stainz - mXion Modellbahntechnik. But would like to look at an installation manual before committing to buying it. Hope there is no need to cut too much into the metal weights.

As for the speaker, wont the speaker that comes with the decoder be of a slight better sound quality than the starter set speaker? The Stainz seem to have a quite roomy speaker section. Any extra cable should be possible to hide (or use the same path as the original speaker I think. But would have to find the mXion decoder manual to know more.

The mXion also seems to come with a power pack? I would assume that has to be placed on the floor next to the driver figure

Yes, welcome to GSC, there are plenty of folks on here to help! :)

Jon.
Yes! Was using AI for assistance during the initial attempt, but it got stuck so many times and started guessing. Seems there isn't much "training data" out there for the lesser popular G scale model side of model railroad. Glad to see forums like these in good health :)
When you reassemble the loco you will find you have 2 weights left over. They should have been put in the side tanks!
Almost forgot them, but thankfully saw them on the desk just before the two halves went together!
 
You can download all the mXion manuals from their website, so you can read up on it all before you purchase! :)

I'm not sure what you mean by a "power pack"? The unit in the picture with a very big capacitor is actually the SX6 SUSI sound module, I think the one in the photo might be an earlier design than they one they currently supply; I bought a couple of mXion decoders and sound modules recently and the current SX6 looks different from that one.

Jon.
 
You can download all the mXion manuals from their website, so you can read up on it all before you purchase! :)

I'm not sure what you mean by a "power pack"? The unit in the picture with a very big capacitor is actually the SX6 SUSI sound module, I think the one in the photo might be an earlier design than they one they currently supply; I bought a couple of mXion decoders and sound modules recently and the current SX6 looks different from that one.

Jon.
Just found them! Will have a deeper look later today!

As for power pack, I was thinking of something like a buffer capacitor that you would find on modern HO locos so that it doesn't loose power when dealing with spots of dirty track. But I guess it's less of a problem on these massive G scale locos with a lot more contact surfaces :)
 
Just found them! Will have a deeper look later today!

As for power pack, I was thinking of something like a buffer capacitor that you would find on modern HO locos so that it doesn't loose power when dealing with spots of dirty track. But I guess it's less of a problem on these massive G scale locos with a lot more contact surfaces :)

As I mentioned, I think the thing you're looking at in the picture is actually the SX6 sound module, possibly an older version of it - but regarding Power Buffers, you can get those for G scale locos, of course - and if you have room for one then it's never a bad idea for a short-wheelbase loco like a Stainz, especially if you're going to be running outdoors. Any loco using the short 4-wheel motor unit can easily get a bit jittery on dirty track, even with the pickup skates - and even more so over point frogs, especially the longer frogs on larger-radius points...

You can also make your own "budget" power buffers, as explained here: Old thread for a cheap and simple Power Buffer...?
....although you do have to disable the analogue-running option in the decoder if you fit one of these, or it can confuse things a bit!
Jon.
 
Back
Top Bottom