New coal mine complex

Mik

Steam tractors, good books, scratchbuilding models
This is going to be a multi building complex before we're finished, so bear with me.

The first building is a remake of the old mine tipple. I made a new base to allow it to serve 2 tracks. -- If it looks sort of like a Piko house on stilts, it is.
P3260001.jpg


I painted it dark ultra flat brown. The roof is a satin ivy green... It looked OK, but not quite what I wanted
P3260004.jpg


Out came the coffee stirrers.... MUCH better - or it will be after I build the bony trestle and give it another coat of paint.

P3270001.jpg


The tipple will connect to the next building on a lower level via a long covered incline. Unfortunately, I sheared off the drive in my B&D rotary tool, so I'll have to buy a new one first....
 
Thats looking really good.
 
Building #2, the mine car dumper--
P3280001.jpg


OK, so the building is empty. It's where the dumper would be if I actually built one... This shack will connect to the other end of the above mentioned covered incline. It will have two 32mm tracks entering the front (loaded cars in, empties out) -- Except the live track will actually exit the rear and into another building. It was too wet today to paint, but this building will also be the same brown/green combo as the tipple just as soon as it quits raining.
 
Mik said:
This is going to be a multi building complex before we're finished, so bear with me.

The first building is a remake of the old mine tipple. I made a new base to allow it to serve 2 tracks. -- If it looks sort of like a Piko house on stilts, it is.
P3260001.jpg


I painted it dark ultra flat brown. The roof is a satin ivy green... It looked OK, but not quite what I wanted
P3260004.jpg


Out came the coffee stirrers.... MUCH better - or it will be after I build the bony trestle and give it another coat of paint.

P3270001.jpg


The tipple will connect to the next building on a lower level via a long covered incline. Unfortunately, I sheared off the drive in my B&D rotary tool, so I'll have to buy a new one first....

it tht piko saloon?......
 
It was the church/school... they're the cheapest
 
Really looking forward to seeing how this turns out- not enough grotty industry modelled in G scale in my opinion!
 
Moving right along... today's project was the machinery shed. The back half houses the steam engines that drive the ventilator for the mine, and the conveyor to the tipple. The front half is a maintenance building... In reality all it will actually do is hide part of the tram loop.I need to install a railing and 2 bay doors, but I haven't yet decided what color the doors should be.
P3290001.jpg


P3290002.jpg


Our complex so far...
P3290003.jpg


One more major structure to make. A boiler house. Plus a few sheds and, of course, the mine entrances...
 
Well done Mik, they look great
 
Thank you for the kind words.

The auto loader is tempting, except it violates my KISS principle or modeling. The simpler things are mechanically, the less there is to go wrong.

I admit, 'operations' just aren't my thing. Turns playtime into too much like work. I like building stuff, then putting on some big band music and watching them run.
 
I started to lay out the boiler house today.... Geez, but it's going to have to be HUGE to fit an entire half circle of the e-train track inside! (I forgot that the diameter was 77cm! (almost 30") ) We're talking about a single structure 35" long x 17" deep x 12" tall (less smokestacks) - for a scale 70 feet long!.... Just about twice as large as anything I've attempted to build from acrylic so far!

Here is the pic of the boiler house at Iselin, Pa. again, to give you an idea.
indiselin4.gif


I'll add pics of my efforts later this evening....
 
Pix, as promised...

The boiler house at Florence, Pa., Jefferson Co. ca 1905

jefflorence1910.gif



First was the floor. This took 4 pieces just to make it big enough!....

P4130001.jpg



back corner...
P4130002.jpg


2 pieces aren't quite long enough, I'll need to splice another bit on... I'm attaching the scale house to the side of the boiler house to help hide the loop.

P4130003.jpg


Never try to paint with an almost empty rattle can.... Good thing this is just the base coat!
P4130006.jpg



The paint and glue needs to harden a bit more (and outgas!) before I start on the next phase of construction
 
Hi Mik, been watching this thread with interest - all looks great by the way! Quite a large complex (even in G scale). What glue do you use for fixing the wood to the plastic?
Mick
 
Today I made 2 of the adits. One is actually a drain pipe to prevent rainwater from flooding the mine area. The other is just for looks... I may add another adit, and I may frame them all with timber.... I'm not sure yet.
P4200002.jpg


Another view...
P4200001.jpg


I just couldn't resist roughing out the tram trackage, just to make sure everything would fit. There will be a couple more turnouts and a crossover in the final version. But I have to pour a bit of concrete first.
P4200003.jpg


P4200004.jpg
 
The arrival of more 32mm track yesterday, and a break in the rain today allowed me to make some progress. I had to relocate one of the adits to allow for the sectional track. I think it all looks fairly proper and functional.

P4250001.jpg


P4250002.jpg


P4250003.jpg


Rockwork or jigsaw puzzle?
P4250004.jpg
 
Wellllllll, I guess I've been away from this project longer than I thought.

Today I FINALLY set the tipple and made the conveyor (a section of square plastic downspout - fast n' easy).
P7110002.jpg


P7110003.jpg


P7110004.jpg


Still need to make a boney pile. under the chute
P7110005.jpg
 
Five Star model; great stuff!!! Will the mine tramway work, too? What sort of stock will it have?
 
Back
Top Bottom