xls decoder into a lgb s22741 spreewald

D

DRG11

Registered
Country flag
Hi All, Many thanks to all for your previous help with the Piko locos which are now all sorted,

Im looking at putting a XLS decoder into the LGB 22741 2-6-0 Spreewald loco but am having problems working out where it goes !!!

On the Piko locos I took the boards out and replaced them with XLS decoders but will this work with the Spreewald, or is it a case of plugging the decoder in ?

Any help please as I cannot find anything about this here unless ive missed it.

Many thanks for your help, stay safe and keep on running !!!
 
DRG11 said:
Hi All, Many thanks to all for your previous help with the Piko locos which are now all sorted,

Im looking at putting a XLS decoder into the LGB 22741 2-6-0 Spreewald loco but am having problems working out where it goes !!!

On the Piko locos I took the boards out and replaced them with XLS decoders but will this work with the Spreewald, or is it a case of plugging the decoder in ?

Any help please as I cannot find anything about this here unless ive missed it.

Many thanks for your help, stay safe and keep on running !!!
Click to expand...
According to the books it will have an on board decoder fitted. Thus it looks like you will have to do the same as you have with the Piko I think. Someone will tell if I am wrong on this.
 
It has a factory fitted MTS decoder so you would have to remove that. As it is only one motor an LS would do if you can get one, they are cheaper but hard to source. You may be able to unplug the lighting plugs from the old decoder and use them on the replacement decoder if you are lucky.
 
Personally, the easiest if its a MTS Onboard decoder (as the service diagrams indicate), replacing it with an XLS-OB is the best option as its a simple swap.

I don't have any in stock but can order and install the correct sounds if needed.

www.gardenrailoutlet.co.uk

Massoth eMotion XLS Onboard Sound Decoder

The LGB Onboard Decoder has proven itself a thousand times since the turn of the millennium. But development has not stopped at this level. Especially Garden Railroaders regret that many functions of Massoth decoders are not available on LGB Onboard Decoders. The brand new XLS-Onboard...
www.gardenrailoutlet.co.uk

LS decoders are available but again at this moment I do not have any but are shown as available so can order if needed.

www.gardenrailoutlet.co.uk

Massoth eMotion LS Sound Decoder

The little brother of eMOTION XLS sound decoder is suited to fit significantly smaller locomotives. The function range corresponds to the XLS. Only the motor current is optimized for a single motor locomotive and the number of function connections is minimally reduced due to the size. Besides...
www.gardenrailoutlet.co.uk


And for reference - link to the service diagram:

 
Many thanks gents,

As I already have the XLS from you MUMS I will look at putting it in,

Thankyou again for your help, stay safe and keep running :)
 
Hello all,

Im obviously missing something here as ive taken out all the lgb boards but when i attach the xls the loco just goes as if its got a connection at all times ?,

Ive done the same as ive done on the piko locos which work fine so not sure what ive done wrong here, any help please.

The underside of the loco has not been toudhed and as ive read on the lgb its the inside 2 pins are pick ups and the outer 2 to the motor but the loco just goes as soon as you put onto the track which does not make any sence at all !!!

Any assistance please or if anybody has done this do they have a photo of the board (ls or xls) on the loco not using the lgb electrics.

Many thanks for your help.
 
A while since I put an XLS in mine but I found a photo showing connections. Maybe it will help.

Step 16.JPG

Note that mine was non-sound - not sure if that matters if you've removed all the factory-fit LGB gubbins but thought it worth mentioning.
 
If you do not have any other boards, then you either have a wiring fault, or a faulty decoder..

Can you post a picture of your installation, please?
 
DRG11 said:
Hello all,

Im obviously missing something here as ive taken out all the lgb boards but when i attach the xls the loco just goes as if its got a connection at all times ?,

Ive done the same as ive done on the piko locos which work fine so not sure what ive done wrong here, any help please.

The underside of the loco has not been toudhed and as ive read on the lgb its the inside 2 pins are pick ups and the outer 2 to the motor but the loco just goes as soon as you put onto the track which does not make any sence at all !!!

Any assistance please or if anybody has done this do they have a photo of the board (ls or xls) on the loco not using the lgb electrics.

Many thanks for your help.
Click to expand...
The wiring of the Piko Locomotives is not the same configuration as LGB. I have been looking at pics of some of my bashes to get the Piko configuration but I am pretty sure that is the order from the motor block.

Piko
Red Motor
White Track
Grey Track
Blue Motor

LGB
Yellow Motor
White Track
Brown Track
Green Motor

Trainline
Blue Motor
Yellow Track
Red Track
Green Motor
 
Hi Philip and all,

Ive changed the decoder and it works so it seems like it was a dodgy decoder,

Many thanks to all :)
 
DRG11 said:
Hi Philip and all,

Ive changed the decoder and it works so it seems like it was a dodgy decoder,

Many thanks to all :)
Click to expand...

Suggest you try doing a reset of the XLS decoder on your programming track. You'll need to wire it to your test stand loco, or use the Massoth PC Module, or the Massoth Service Board.
 
You must log in or register to reply here.
Back
Top Bottom