R/C Not working

Hekate

Registered
21 Apr 2017
42
10
75
Normandy
Best answers
0
The next problem I have is that the DIMAX Navigator does not work in R/C mode. Tethered it works fine. The red light is on the Receiver but the Navigator shows a black cross through the loco picture on the screen. It worked fine the last time I used it. Any ideas ?
 

Gizzy

A gentleman, a scholar, and a railway modeller....
26 Oct 2009
36,149
2,278
63
Cambridgeshire
www.gscalecentral.net
Best answers
0
Country flag
Have you tried resetting or repowering both Navigator and Z1200....
 

Hekate

Registered
21 Apr 2017
42
10
75
Normandy
Best answers
0
I have turned them on/off multiple times, tried a new cable. Replaced batteries in handset, cleaned contacts in receiver, Can`t think of anything else !
 

stockers

Trains, aircraft, models, walking, beer, travel
24 Oct 2009
25,631
3,795
65
Nr. Ashford, Kent. England.
Best answers
0
Country flag
Check the radio is fitted tight and check the receiver module. Is the ariel inserted?
 

Hekate

Registered
21 Apr 2017
42
10
75
Normandy
Best answers
0
I have cleaned up the end of the aerial, also the socket it goes into, still not working. It could be a fault with the receiver but at £100 a time I don't want to buy another one on the off chance.
 

Neil Robinson

Registered
24 Oct 2009
9,699
579
N W Leicestershire
Best answers
0
Country flag
I wonder if changing the radio transmitter channel would have any effect.
 

Ralphmp

Registered
6 Jan 2010
1,640
228
72
Herts
Country
England
Best answers
0
Country flag
Does the Navigator display show there is a link with the central station? (There should be a picture of an antenna in the top right corner next to the battery symbol)
If you don't have this, it's worth confirming that the Navigator RC channel matches that of the wireless receiver as described in section 8.9 of the Navigator manual (downloadable from the Massoth Wiki).
If you do, then try editing an existing loco config or creating a new one, and then see if you can connect to a loco. I have had the "black X" on a couple of occasions and when the usual power off/on didn't work, the create/edit did the trick.
 

stockers

Trains, aircraft, models, walking, beer, travel
24 Oct 2009
25,631
3,795
65
Nr. Ashford, Kent. England.
Best answers
0
Country flag
Good suggestions Phil. Why didn't i say that!
 

Ralphmp

Registered
6 Jan 2010
1,640
228
72
Herts
Country
England
Best answers
0
Country flag
Just coincidence! I've been looking at R/C channels recently as I'm trying to work out if I need to make any changes to have 2 Navs and a Feedback module connected wirelessly to my central station.
 
D

Deleted member 1986

Guest
The next problem I have is that the DIMAX Navigator does not work in R/C mode. Tethered it works fine. The red light is on the Receiver but the Navigator shows a black cross through the loco picture on the screen. It worked fine the last time I used it. Any ideas ?

Navigator Transmitter and the Receiver are set to TWO different RC Channels ?......

RC.PNG

RC 1.PNG
 
Last edited by a moderator:

stockers

Trains, aircraft, models, walking, beer, travel
24 Oct 2009
25,631
3,795
65
Nr. Ashford, Kent. England.
Best answers
0
Country flag
Just coincidence! I've been looking at R/C channels recently as I'm trying to work out if I need to make any changes to have 2 Navs and a Feedback module connected wirelessly to my central station.
All on the same channel.
 
D

Deleted member 1986

Guest
Just coincidence! I've been looking at R/C channels recently as I'm trying to work out if I need to make any changes to have 2 Navs and a Feedback module connected wirelessly to my central station.

As well as all being on the same RC Channel, each wireless device requires a separate individual ID.
 
Last edited by a moderator:

Tanker man

G scale and 5 inch ride on
10 Jun 2015
746
264
Oxford
Best answers
0
Country flag
I had this happen to me on my last open day two years ago, everything had been working fine then it just stopped. My receiver is under a 2 Ltr bottle cover on the stub branch of a tree, to give me the widest coverage of signal, on inspection, I found a family of Earwigs had moved into the blue box! Nothing I could do, after evicting said tenants, would make the receiver work. It went back to Massoth via 'Muns' , and the repair cost me £14 . It now works fine again, but I have sealed it inside the cover now. There was no explanation from Massoth as to what the problem was. It was a little annoying being away for several months but better than £100 for a new one, and I could still use the railway with the handsets tethered.
Dave